SCH6200 - 6299
SCH6200 | The BRSC must be disabled first. Action: Disable the BRSC in LD 32. |
SCH6201 | Input is not a BRSC card TN. Action: Enter a BRSC card TN. For PRT command, you can enter {cr}, loop, or loop shelf. |
SCH6202 | slot Card slot is configured. Where: slot = all available slots in the IPE shelf. Action: Configure the BRSC in one of the slots listed. |
SCH6203 | tn A BRSC (tn) is configured in the IPE shelf. Action: Configure the BRSC in another IPE shelf. |
SCH6204 | tn Disable BRI line cards (tn) first before adding a BRSC or removing. Action: Disable all line cards listed in LD 32. |
SCH6205 | Cannot use MPH for DPSD because at least one DSL on the same IPE shelf has a LTEI pair
defined. Action: Remove all LTIDs or use a PRI B channel for accessing the Packet Switched Data Network(PSDN). |
SCH6206 | Cannot use PRI Channel for DPSD connection because at least one DSL on the same IPE
shelf has a DPSD TSP defined. Action: Remove all DPSD TSPs or use MPH for accessing the Packet Switched Data Network(PSDN). |
SCH6207 | Cannot add a BRSC to this MISP. MISP has MPH application configured. Action: Pick another MISP without MPH application or remove the application. |
SCH6208 | Cannot add a BRSC to this MISP. MISP has maximum number of BRSCs configured. Action: Pick another MISP. |
SCH6209 | Cannot add a BRSC to this MISP. MISP has too many LC configured. Action: Pick another MISP, or remove some line cards and disable the MISP. |
SCH6210 | The MISP must be disabled first. It was programmed to handle 4 line cards. Action: Disable the MISP in LD 32. |
SCH6211 | The MISP must be disabled first. It was programmed to handle 3 line cards and 1 BRSC. Action: Disable the MISP in LD 32. |
SCH6212 | The MISP must be disabled first. It was programmed to handle 2 line cards and 8 BRSCs. Action: Disable the MISP in LD 32. |
SCH6213 | Cannot add a BRSC to this MISP because it does not have MPH application configured. Action: Pick another MISP with MPH application, or configure the MISP with MPH application first. |
SCH6214 | Cannot add a BRSC to this MPH MISP because it has the maximum number of SAPI16
connections configured. Action: Pick another MPH MISP or remove one SAPI 16 connection from this MPH MISP first. |
SCH6215 | There are DSLs with both LTIDs and TSPs for D-channel PSD configured. Action: If D-channel PSD is going to be provided and MPH is used, remove all configured LTIDs. If D channel PSD is going to be provided and an external packet handler is used, remove all configured TSPs for D-channel PSD. Otherwise, remove all LTID pairs AND TSPs for D-channel PSD. |
SCH6216 | There are DSLs with TSPs for D-channel PSD configured. Action: Remove the TSPs for DPSD first. |
SCH6217 | There are DSLs with LTIDs for D-channel PSD configured. Action: Remove the LTIDs first. |
SCH6218 | Cannot remove the MISP because at least one BRSC is associated with it. Action: Disassociate the BRSCs by deleting them or change their Layer 3 MISP. |
SCH6219 | Cannot add BRI line card to this MISP because it has the maximum number of line cards
configured. Action: Add a BRSC to the IPE shelf, delete some line cards, or use another MISP. |
SCH6220 | Cannot remove or modify a BRSC because background maintenance task is in progress. Action: Wait until the task is done or disable the BRSC in LD 32, then repeat the command. |
SCH6222 | The USR key must be removed before changing the telephones Class of Service to DTA. |
SCH6223 | The TRIGGER string entered is not in the filter/exception table. Action: Check then enter a correct string. |
SCH6224 | Another user is already accessing that TN. |
SCH6225 | Another user is already accessing that DN. |
SCH6226 | A telephone with an ACD key cannot be assigned CCSA Class of Service. |
SCH6227 | A telephone with CCSA Class of Service, or non-zero SCI cannot be assigned an ACD key. |
SCH6228 | ITPP=YES and METR=XPXX are incompatible. |
SCH6229 | ARFW package is not equipped. |
SCH6230 | Input is not a valid RAN route. Action: When reprompted for RANR, a valid RAN route should be entered |
SCH6231 | Too many digits entered for DGTS. Action: When reprompted for DGTS, the correct number of digits should be entered. |
SCH6232 | The interface type entered is incompatible with a CTYP of DCHI or SPDC. The CTYP must be MSDL. (To replace current version) |
SCH6233 | The OHAS DN index is illegal. There is no ODN defined for it in LD 15. Action: Check and enter a legal index. |
SCH6234 | A legal OHID index must be defined to have ASCA Class of Service. |
SCH6235 | A legal FSVC index must be defined to have ASCA Class of Service. |
SCH6236 | No legal ODNs are defined in LD 15. Action: You must define the ODN before assigning indices. |
SCH6240 | A telephone cannot use an ODN that is to be deleted. Action: Be sure the deleted ODN is not used by any telephone. |
SCH6242 | Signaling must be standard when Equal Access toll call restrictions have been enabled for this route. (EQAR = Yes). Action: Remove the Equal Access toll call restrictions for this route by setting EQAR to No prior to changing the signaling arrangement. |
SCH6243 | DTI TIE routes must be voice only when Equal Access toll call restrictions have been
enabled for this route. (EQAR = Yes). Action: Remove the Equal Access toll call restrictions for this route by setting EQAR to No prior to changing the voice and data calls type. |
SCH6245 | That TN is not available. Action: Use another one. |
SCH6246 | Cannot build/tear down the tandem connection. Action: Check the PRI status |
SCH6247 | Cannot remove this TIE trunk because there is a tandem connection associated with it. Action: Remove the tandem connection, then remove the trunk. |
SCH6252 | The MOV DCH command is not supported by Option 11. |
SCH6253 | ISLD/VNS/VNSA user modes are not supported by the option 11 downloadable D-channel feature. Only shared modes SHA and SHAV can be used, as well as PRA and PRI. |
SCH6261 | The PNI number just entered is the same PNI number as currently programmed |
SCH6262 | % Maximum of 100 steps are allowed only. |
SCH6263 | BRIL and MPH applications may not be configured on the same MISP. |
SCH6264 | The ISA service route cannot be removed because there are calls active on that route. |
SCH6265 | Digits for insertion may be an invalid DN. |
SCH6266 | This DN cannot be removed from the Group Hunt list as it belongs to a set being relocated; moreover, the list cannot be outed, or resized down as to exclude this DN. |
SCH6267 | This DN cannot be added to a Group Hunt list as it also belongs to a set being relocated. |
SCH6268 | The response entered is not valid for the current ISDN IFC. |
SCH6269 | IFC (CNTY) does not correspond to the given DGTP. |
SCH6270 | Incorrect PWD2 password entered. Access to Loss Planning Data is not allowed. |
SCH6271 | DLSA is disabled. If any B34/B39 cards in the system, SLPD installation procedures must follow. |
SCH6272 | Start Arrangement for L1 signaling must be SEZA or PTSD. |
SCH6273 | Start Arrangement for RON/TRON signaling must be RT. |
SCH6274 | Only LDR signaling is allowed for TIE trunk on XDID. |
SCH6275 | The number of Meridian 1 Packet Handler Digital Subscriber Loops (DSLs) in the system has reached the limit. |
SCH6276 | Warning: External DN of IDC tree not stored in corresponding SDID tree to prevent overwriting existing value. This inconsistency occurs in the SDID tree when more than one external DN terminates on the same internal DN in the IDC tree. |
SCH6278 | Value out-of-range for TABL prompt. Accepted values are 0-15 Action: Check the customer documentation on TDS tone tables. |
SCH6279 | Overlay code is compressed, but the decoding table does not exist. |
SCH6280 | Class of Service HSPA and TSA are exclusive. |
SCH6281 | KD3 package not equipped. |
SCH6282 | CLS cannot be configured as MFK TN is DID and DTI2. |
SCH6283 | Overlay 16 - Warning - MFK Outgoing table will be cleared. Route members should not have MFK CLS if there is no incoming MFK table. |
SCH6284 | Overlay 16 - Warning - MFK Incoming table will be cleared. Route members should not have MFK CLS if there is no outgoing MFK table. |
SCH6285 | Overlay 16 - Attempt to mark a non-digital, non-DID route as MFK5 or MFK6 type of signalling. |
SCH6290 | The CLS DPDT or DTDP can be configured on routes with ICOG IAO only. Action: Check trunk configuration. |
SCH6291 | The CLS DPDT or DTDP can be configured on analog DID or TIE trunks only. Action: Check trunk configuration. |