SCH5800 - 5899
SCH5803 | CPU number out-of-range (0-1). |
SCH5804 | The specified CNI port is in-service. Action: Disable the CNI port before changing it. |
SCH5805 | The specified group is configured for other CNI port. |
SCH5806 | The specified slot is configured other than as CNI. |
SCH5807 | Slot already exists for other card. |
SCH5808 | Error occurred in printing CINV. |
SCH5809 | TSA and ASA class of service are mutually exclusive. |
SCH5810 | Yellow alarm pattern of FDL can only be specified for ESF framing format. The software automatically enters YALM = DG2. |
SCH5812 | Cannot delete DNCO, still in use. |
SCH5813 | A USR key cannot be configured on a data set (CLS DTA). |
SCH5814 | A set cannot have USR key with USRD Class of Service. |
SCH5815 | Terminals Ringing Cycle Option (RCO) was reset from {old RCO} to default value 0, because the CLS was changed to FND and MWD. |
SCH5816 | Warning: PBXT test scheduled for automatic execution in the daily routines |
SCH5817 | CONF loops can only be defined on loops 29, 30 & 31 for Option 11. |
SCH5818 | Cannot define CONF loop on loop 31 if only 1 cabinet defined. |
SCH5819 | The VAS is in use in the customer data block under the VSID prompt. Action: Delete the VAS from LD 15, then remove it from LD 17. To clear the VAS, use LD 15, and go to the VSID prompt. |
SCH5820 | The VAS ID is in use by a CCR, Meridian Link, or Data application. Action: Remove the VAS by using LD 23, then delete the VAS from LD 17. |
SCH5821 | The VAS ID is in use by the teleset-messaging. Action: Remove it in LD 23, then delete it from LD 17. |
SCH5822 | The VAS ID is in use by the teleset-status. Action: Remove it in LD 23, then delete it from LD 17. |
SCH5823 | The VAS ID is in use by the CCR, or the Meridian Link application. Action: Remove it in LD 23, then delete it from LD 17. |
SCH5824 | The VAS does not exist. Action: First create the VAS in the LD 17, then use it in LD 15. |
SCH5825 | This loop cannot be removed until its associated DDSL has been removed first. |
SCH5826 | Cannot change or print the Class of Service MREA/MRED in the TN block without the
option enabled in LD 15. Action: Enable NMDR/DMDR in LD 15 before attempting the change. |
SCH5827 | Cannot assign a greater value to NMDR than to CFNA. Cannot assign a greater value to DMDR than to DFNA. Need to assign a value that is less than the value of CFNA or DFNA. |
SCH5828 | ARP only authorized for CO Trunks. |
SCH5829 | Maximum Dial Pulse time has to be greater than Minimum Dial Pulse time. |
SCH5830 | You cannot delete, add, and change a loop at the same time. |
SCH5831 | TSA not allowed while FTR = PHD. XFA prerequisite. |
SCH5832 | BPO type not allowed for XEM. |
SCH5833 | ARP only authorized for COT trunk. |
SCH5834 | Maximum Dial Pulse Time has to be greater than the minimum Dial Pulse Time. |
SCH5835 | Minimum Hook Flash Time has to be greater than the minimum Dial Pulse Time. |
SCH5836 | Access code contains an invalid character. |
SCH5837 | XPE package 203, SUPP package 131 or both packages are restricted. |
SCH5838 | No predefined table or customized table has yet been built for B34 Static Loss Plan.
This is a prerequisite for B34 Dynamic Loss Switching. Action: Configure a table for B34 Static Loss Plan (TTYP = STAT) before configuring a table for B#$Dynamic Load Switching. |
SCH5839 | Action: Contact system distributor to request the LAPW package; otherwise, log into the system using appropriate password which is authorized for changes to "configuration data", or contact system distributor to have this data updated. |
SCH5840 | When entering a customized Static Loss Plan Table (Base Level Table) or a customized
Dynamic Loss Plan Table (Alternative Level Table), {cr} will not be allowed if a table has
not been previously installed. Action: Enter all values for Rx and Tx or begin the command over and install a standard Predefined table, then customize a few values as required. |
SCH5841 | Wrong number of parameters have been entered. Action: Enter two values, one for Rx, and the second for Tx (or enter {cr} only) for all port types except RANR and PAGT. Enter one value for RANR (Rx) and PAGT (Tx), or enter {cr} only. |
SCH5842 | B34 Dynamic Loss Switching is disabled. B34 Codec Static Loss Downloading is now in
effect. Action: Enter two values, one for Rx, and the second for Tx (or enter {cr} only) for all port types except RANR and PAGT. Enter one value for RANR (Rx) and PAGT (Tx), or enter {cr} only. |
SCH5843 | The Table Number value entered is out-of-range. Action: Enter a Table Number within the range, [1-25] for STYP, and [1-2] for DTYP. |
SCH5844 | The coded Relative Input/Output Level (Rx or Tx) value is out-of-range. Action: Enter correct ranges as follows: Rx - (0 - 31)Tx - (8 - 39) |
SCH5845 | Cannot change number of AOMs because it deletes the BFS key. Action: Remove BFS key first. |
SCH5846 | You answered YES to the DITI prompt, but the DID to TIE package 176 is equipped. DID to TIE calls are restricted by the DID to TIE package. |
SCH5847 | CNI slot 8, port 0 cannot be changed or deleted. |
SCH5848 | The specified application is not configured on this MISP. |
SCH5849 | BRI trunk types can only be TIE, COT, and DID. |
SCH5850 | Cannot change these parameters without disabling all associated BRI trunk members. |
SCH5851 | Interface type not valid for Basic Rate. This message indicates that the IFC trunk entered does not support Basic Rate trunks. |
SCH5852 | Cannot out BRIL application without disabling the application. |
SCH5853 | Cannot out BRIL application without outing all the associated DSLs. |
SCH5854 | The specified route is not a BRI route. |
SCH5855 | BRIT package is not equipped. |
SCH5856 | The new MISP for this card does not have BRIL configured, but there is a BRIL DSL on this card. |
SCH5857 | BRI route is not allowed if a BRI Route Packet Handler exists. |
SCH5858 | PRI is not supported if the DTI2 package and the PRI2 package are not equipped. |
SCH5859 | A DSL trunk in NT mode must be associated with a route on NET side. |
SCH5860 | Protocol group cannot be removed. Remove the route(s) associated with this protocol and try again. |
SCH5861 | Cannot out BRIT application without disabling the application. |
SCH5862 | Cannot out BRIT application without outing all the associated DSLs. |
SCH5863 | The new MISP for this card does not have BRIT configured, but there is a BRIT DSL on this card. |
SCH5864 | BRIL package is not equipped. |
SCH5865 | ISDN option needs to be configured in the Customer Data Block before a BRI route can be configured. |
SCH5866 | Either the BRIL or the BRIT package needs to be equipped. |
SCH5867 | Line card is not a BRI SILC line card. |
SCH5868 | {cr} is not allowed at TNUM prompt. Action: Enter a Table Number within the range, [1-25] for STYP, and [1-2] for DTYP. |
SCH5869 | Line card must be SILC for Numeris DSL. |
SCH5870 | Warning: Another device is configured on the same card. Action: Change the group number as well. |
SCH5871 | Warning: There may be other devices on the QSDI card. Action: Be sure the group number corresponds. |
SCH5872 | NPID table does not exist. |
SCH5873 | The NPID type cannot be entered because M911 package 224 is not equipped. |
SCH5874 | NPID table already exists. Action: Use CHG command. |
SCH5875 | NPID table does not exist. Action: Use NEW command. |
SCH5876 | M911_NPID_MHPTR is Nil. |
SCH5877 | NPID table out-of-range (0-7). |
SCH5878 | All applications on the MSDL card are affected by the group number change. |
SCH5879 | The Filter trigger entered is identical to an Exception trigger, or the Exception
trigger entered is identical to a Filter trigger. Action: Enter a different string or change the other Filter/Exception string. |
SCH5880 | The mnemonic entered is invalid. Action: Check and re-enter the desired mnemonic. |
SCH5881 | The error code entered is invalid. Valid characters are 0-9 and + (plus sign). Action: Check and re-enter a valid character. |
SCH5882 | The SUPPRESS threshold cannot be less than the ESCALATE threshold. Action: Check and re-enter the desired threshold. |
SCH5889 | Entered a number outside of the range allowed for the parameter for NEW and CPY
commands in LD 18. The valid range is 1-100. Action:Re-enter the NEW or CPY command with a new parameter between 1 and 100. |
SCH5890 | Available memory is below the minimum allowed when trying to add multiple speed call
lists at once using the NEW and CPY commands in LD 18. Minimum is 2048 words. Action: Create the Speed Call lists one at a time, or free up additional memory. |
SCH5891 | With X11 Release 19 and later, use one of the following formats for DN block printing: 1. multiple DNs may be printed by listing them at the DN prompt using commas to separate the individual DNs 2. a range of DNs may be entered using a dash between the starting and ending DNs |
SCH5892 | Tried to disable B34 Static Loss Plan Download (SLPD) feature while B34 Dynamic Loss
Switching (DLS) is still enabled. B34 SLPD not disabled. Action: Disable B34 DLS before disabling B34 SLPD. |
SCH5893 | BIMP value not apply to XUT. |
SCH5894 | 1200 OHM Termination impedance not apply to EXUT. |
SCH5895 | Cannot select PSP/PIP without MR feature ON. |
SCH5896 | DWC keys DN does not match the ACD DN of the queue the agent is in. |
SCH5897 | AWC key is already defined for this agent. |
SCH5898 | DWC key is already defined for this agent. |
SCH5899 | The appropriate DSL on this card (DSL #0 for PREF or DSL #1 for SREF) must be a trunk DSL. |