SCH2000 - 2099
SCH2000 | An attempt was made to assign a mini CDR tape unit to a customer for which the tape
was not assigned in configuration data. Action: Assign the tape in LD 17 and return to LD 15 to assign the tape to a customer. |
SCH2001 | Private route not allowed. |
SCH2002 | No CDP list exists for this CDP steering code. |
SCH2003 | ESN data block does not exist for this CDP steering code. |
SCH2004 | No customer data block exists for this CDP steering code. |
SCH2005 | Invalid CDP steering code. |
SCH2006 | Wrong number of input fields for prompt NCOS. |
SCH2007 | NCOS number out-of-range (0-15 for NARS, 0-3 for BARS/CDP, 0-7 for NFCR). |
SCH2008 | NCOS package must be equipped if ESN is entered. |
SCH2009 | NARS package must be equipped if ETN is entered. |
SCH2010 | Signaling type inconsistent with card density. |
SCH2011 | New unit number is too high for the new card. |
SCH2012 | Off-premise extension for single density card only. |
SCH2013 | Attempt to increase card density while OPX units are equipped. |
SCH2014 | Existing card density too high for move/swap. |
SCH2015 | Attempt to move/swap loops while upper shelves exist in the loop with lower density. |
SCH2016 | The DNIS Route must be defined as auto-terminating or IDC. |
SCH2017 | This value represents a change for the CDR with Outpulsed Digits (OPD). The change does not take effect until after the next initialization. |
SCH2019 | Frame formats must be the same when moving or swapping DTI loops. |
SCH2020 | Moving a trunk between different loops is not permitted. |
SCH2021 | DTI package not equipped. |
SCH2022 | Cannot delete a non-DTI loop or add a DTI loop which is not undefined, or make changes to a non-DTI loop. |
SCH2023 | Odd loop numbers for DTI card slot not allowed. |
SCH2024 | Digital trunk loop must be a DTI2, JDMI, or PRI2 loop. |
SCH2025 | Primary reference loop number and secondary reference loop number cannot be the same. |
SCH2026 | Illegal input for trunk type. |
SCH2027 | NCOS package and/or DTI package is restricted. |
SCH2028 | Digital TIE auto must be VCE or DTA only. |
SCH2029 | TN to channel conversion failure. |
SCH2030 | Digital data block does not exist. |
SCH2031 | Digital data block already exists. |
SCH2032 | Configuration loop number must be a DTI card slot. |
SCH2033 | A DTI loop can only be moved to another DTI loop. |
SCH2034 | A digital route is required. |
SCH2035 | {CR} is allowed only if a DTI card does not exist on the network shelf. |
SCH2036 | Framing format has been changed from D2 to D3 or vice versa. Action: For X11 Release 16, framing format cannot be changed while trunks exist on the loop. Trunks associated with that loop must first be removed from the configuration before changing the framing format. |
SCH2037 | Channel out-of-range (1-24). |
SCH2038 | Channel to TN conversion failure. |
SCH2039 | Last shelf on the slot is not permitted for DTI. |
SCH2040 | Cannot remove a digital data block while DTI loops still exist. |
SCH2041 | Framing format data corruption has occurred. |
SCH2042 | Protected terminal digital loop block pointer has been corrupted. |
SCH2043 | LFTN must be TN with the same customer number. |
SCH2044 | LUC not permitted for DTI loops. |
SCH2045 | Wrong number of input fields. |
SCH2046 | Departmental LDN out-of-range. |
SCH2047 | Invalid input. Attendant number is either out-of-range or an invalid input was encountered. |
SCH2048 | Unable to match input with stored mnemonics. |
SCH2049 | Cannot add existing attendant or delete non-existing attendant. |
SCH2050 | Outing an existing DND group is not allowed unless the GND key is deactivated on the attendant console. |
SCH2051 | Unable to match input field with stored mnemonics for prompt CNVT. |
SCH2052 | ESN digit manipulation index out-of-range (0-255). |
SCH2053 | ESN digit manipulation table does not exist. |
SCH2054 | ESN data block does not exist. |
SCH2055 | Wrong number of input fields for prompt ATDN. |
SCH2056 | Only FDN is allowed for 500 telephone. |
SCH2057 | WTA not allowed for CLS DTA. |
SCH2058 | Null input not allowed for prompt NEW. |
SCH2059 | Wrong number of input fields for prompt MTN. |
SCH2060 | Release 8 L MSI configured in SCC FN. Prompt incoming default not allowed. |
SCH2061 | Too many ranges defined for this location code (20 ranges maximum). |
SCH2062 | Overlapping or duplication of ranges. |
SCH2063 | XRA or XFA not allowed when CLS = MNL. |
SCH2064 | The desired key is already defined. Action: Only one CSD is allowed for each set. |
SCH2065 | PBX ring option conflicts with group option. |
SCH2066 | Wrong key number to TAD. |
SCH2067 | The Call Park option must be allowed (CPA) in CDB. |
SCH2070 | Cannot OUT customer when ESN, NCTL or AUTH blocks still exist. |
SCH2071 | Cannot OUT customer when ACD still exist. |
SCH2072 | Cannot OUT customer when DISA blocks still exist. |
SCH2073 | Cannot OUT customer when Call Park blocks still exist. |
SCH2074 | Input AOS for CLS = ignored when command is NEW. |
SCH2075 | EFD allowed only with CFTA COS. |
SCH2076 | EHT allowed only with CFTA COS. |
SCH2077 | Unable to match input with mnemonics. |
SCH2078 | CFCT not allowed. |
SCH2079 | BGD user type cannot coexist with ACD, APL, CDL, CMC, CMS, HSL, LSL. |
SCH2080 | BGD customer number must be specified for BGD or PMS Link device. |
SCH2081 | BGD/PMSI package not equipped. |
SCH2082 | PMS user type can coexist with BGD only. |
SCH2083 | SFA must have FNA and MWD specified. |
SCH2084 | SFA not defined. |
SCH2085 | CPND cannot exist with DTA on. |
SCH2086 | SFA not defined. |
SCH2087 | SFA not allowed. |
SCH2088 | ACD-DNIS package is restricted. |
SCH2089 | APL number expected when LINK = YES. |
SCH2090 | Customer option cannot be changed to DNX with DNIS routes defined. |
SCH2091 | Digit insertion not allowed for this DNIS route. |
SCH2092 | DNIS routes cannot be configured with CHG request. |
SCH2093 | Not a valid APL. Define in the Configuration Record. |
SCH2094 | APL package not equipped. |
SCH2095 | NO not allowed for AUTO with DNIS route defined. |
SCH2097 | DN must be ACD DN when trunk is a DNIS route. |
SCH2098 | TDET package is restricted. |
SCH2099 | Multi Party Operation (MPO) Blind Transfer Allowed (MBXA) must have Call Transfer Allowed (XFA) or Three Party Service Allowed (TSA) Class of Service defined. Six Party Conference (C6A) must have Call Transfer Allowed (XFA) Class of Service defined. Permanent Hold (PHD) feature must have Call Transfer Allowed (XFA) Class of Service defined. |