SCH0001 - 0099
| SCH0001 | TNTRANS failed on remove from core. Corrupted data in memory. Action: System should be reloaded. If the fault persists, contact your technical support group. Caution: Call processing will be interrupted during reload. |
| SCH0002 | TNTRANS failed on recover workspace. Action: System should be reloaded. If the fault persists, contact your technical support group. |
| SCH0003 | TNTRANS passes on recover out workspace. Caution: Call processing will be interrupted during reload. |
| SCH0004 | TNTRANS passes on work to core. |
| SCH0005 | RDB translator passes and fails. Corrupted data in memory. Action: System should be reloaded. If the fault persists, contact your technical support group. |
| SCH0006 | The maximum number of MWI NSI tables (32) has been reached. Action: Contact your technical support group if 32 tables are insufficient. |
| SCH0007 | Character out of range B, E< K< N< Q< T< W< b, e, h, k, n, q, t, w,
or z. SUFF is re-prompted. Action: Enter a character inside the valid range or {CR} if CHG command. |
| SCH0008 | Not an alphanumeric character. Action: Enter character(s) inside the valid range or {CR} if the command is CHG or it the prompt is PRMT. |
| SCH0009 | Too many characters for the NSI parameters already entered. MFID is reprompted. Action: Enter a maximum of 126 characters for the total of the MWI NSI parameters. |
| SCH0010 | 0DNXLBLOCK has a pointer flag but no pointer. Corrupted data in memory. Action: System should be reloaded. If the fault persists, contact your technical support group. |
| SCH0011 | TN in DNBLOCK fails TNTRANS. |
| SCH0012 | TN in DNBLOCK produces illegal TN type. Corrupted data in memory. Action: System should be reloaded. If the fault persists, contact your technical support group. |
| SCH0013 | Terminal cannot be moved to a card with different XTRK field (XUS versus non-XUS). |
| SCH0014 | Invalid trunk type for XUS. |
| SCH0015 | XUS trunk unit must belong to an XUS route only, and vice-versa. |
| SCH0016 | In XUS RAN, only LVL and AUD route types are allowed. |
| SCH0017 | If HLPA/HRLA then must IHA. (Individual hold allowed, OPT IHA in CDB, Overlay 15). Action: Configure the IHA in the CDB by using Overlay 15. |
| SCH0018 | Facility number out of range. Action: Input a facility number from 1 to 99999 |
| SCH0019 | Facility number is already defined for that service. Action: Check the subscription parameters with the local CO and input the correct subscribed facility number. |
| SCH0020 | Illegal attempt to modify existing data. |
| SCH0023 | No CLIP list is allowed for this customer (CLIP-MAX=0). |
| SCH0028 | Attempt to configure RCAP with a QSIG Diversion remote capability when one is already
configured. Action: Remove the already configured RCAP before entering a new one. |
| SCH0029 | BCOT initialized due to one of the following conditions: TKTP = ISA, DGTP ^= PRI, MODE ^= PRA, IFC ^= D100 or D250 or ESS4 or ESS5 or NI2 |
| SCH0030 | Digit input instead of alpha input is required. Action: Re-enter only numerals. |
| SCH0031 | Autoline key should have a DN associated with it. |
| SCH0032 | IADN cannot be Attendant Overflow DN. |
| SCH0033 | IADN cannot be a System Night DN. |
| SCH0034 | The RCAP PRI (or PRO) is only allowed for QSIG interface type. |
| SCH0035 | Attempt to configure RCAP to PRI when PRO is already configured. Action: Remove the RCAP PRO first. |
| SCH0036 | Attempt to configure RCAP to PRO when PRI is already configured. Action: Remove the RCAP PRI first. |
| SCH0037 | Autoline key should have a DN associated with it. |
| SCH0038 | IADN cannot be Attendant Overflow DN. |
| SCH0039 | IADN cannot be System Night DN. |
| SCH0040 | ROA/MOH does not exist for specified customer. |
| SCH0041 | Invalid range. Not enough digits. |
| SCH0048 | Not enough memory to allocate a DPNSS1 MWI or MWNS table. Action: Contact your technical support group. |
| SCH0049 | Priority buzz cadence is out of range (2-16 seconds). |
| SCH0050 | ROA/MOH data block already exists. |
| SCH0051 | Attempt made to change a non broadcasting RAN route to broadcasting with an
insufficient number of available ISM RAN connections. Action: Contact your technical support group and request an increase to the ISM limit. |
| SCH0052 | Attempt was made to change a RAN route to broadcasting or non broadcasting with active
calls. Action: Customer must take an action to not have any more active calls to any of the trunk members. Trunks may be disabled or the RAN route may be replaced by another one during the change. This last option will not disconnect any call. |
| SCH0053 | Attempt made to change the maximum number of connections to a broadcasting trunk of a
RAN route in overlay 16, but such a change would exceed broadcast RAN connection ISM
limit. Action: Request your technical support group to increase theISM limit. |
| SCH0054 | Attempt was made to define a RAN route as a broadcast route with an insufficient
number of available ISM broadcasting RAN routes. Action: Request your technical support group to increase theISM limit. |
| SCH0055 | Invalid console type for Individual Attendant DN. |
| SCH0057 | Reduce the MAX value of NI-2 CBC service routes before removing B-channels/trunks. Action: Check the MAX value of service routes |
| SCH0059 | Responses NUM4/NUM6 are not allowed if the MMCS and Master Mode Packages are not
equipped. CNTY is re-prompted. Action: Equip Packages 309 and 317 and re-load. |
| SCH0060 | Insufficient data entered. |
| SCH0061 | The executed operation requires the QSIG-SS package which is restricted. The executed operation is ignored. |
| SCH0062 | The change of a Music broadcast route to a non broadcasting route, is not allowed. |
| SCH0063 | Change of a Music route to a broadcasting route with active calls, is not allowed. Action: Replace the route with another music route. Wait for active calls to be released before doing the change. |
| SCH0064 | The TITH value is out of range (0-300). Action: Enter a value that is in range. |
| SCH0065 | The NCTH value is out of range (0-100). Action: Enter a value that is in range. |
| SCH0066 | The CONN value is out of range (4-48). Action: Enter a value that is in range. |
| SCH0067 | The LGTH value is out of range (4-7200). Action: Enter a value that is in range. |
| SCH0068 | Two sequences starting with the same digits cannot have wildcards : "#". A digit before the wildcard must differentiate between the two to enable them to coexist in the list. |
| SCH0069 | No sequences exist in this list. Action: Use NEW. |
| SCH0097 | The MWI NSI tables for this customer have reached the maximum size allowable. Action: Contact your technical support group if 512 words are not enough for the MWI NSI tables of a customer. |
| SCH0098 | Request to add CMOD unit is rejected. System already has 255 CMOD units configured. |
| SCH0099 | This message appears when the invalid input has been entered for a particular prompt
in an overlay. The actual output may vary, according to the input received. Action: Re-enter prompt with correct input data. Refer to the following examples for possible output. |
| SCH0099 | n?: Input number n out-of-range (0-9999999) for LEC. |
| SCH0099 | n?: 0-7 Input number n out-of-range (0-7) for RDNL |
| SCH0099 | n?: 0-9 Input number n out-of-range (0-9) Action: Choose a number 0 - 9. |
| SCH0099 | XXX XXX is an invalid response. System does not recognize XXX. Action: Try again. |
| SCH0099 | XXX : AAA XXX is an invalid response. System does not recognize XXX. Where: AAA = the system suggestion of a possible match |
| SCH0099 | XXX : BBB CC Abbreviated response XXX has more than 1 matches. Where: XXX = a non-unique abbreviated response AAA, BBB, and CCCC = responses that match XXX Up to 3 matches are listed and "..." indicates more than 3 matches found. |
| SCH0099 | XXX? {MIN} - {MAX} {TYPE} Response XXX is out-of-range. Valid range is specified by
{MIN} - {MAX}, where response type is specified by the following: {TYPE} = Characters for character string input {TYPE} = DigitsS for digit string input No {TYPE} specifies numeric input |