ERR5300 - 5399
| ERR5300 | DPNSS Route Optimization, invalid message received in Route Optimization supplementary service state. The message is ignored. |
| ERR5301 | The ATDN is not a CDN, but the call was routed to the ATDN anyway. Output data: TRK trktn ANI ani_count ani_digits |
| ERR5302 | M911 does not support test calls for the pilot release. (This does not apply to Release 19.) Output data: TRK trktn ANI ani_count ani_digits. |
| ERR5303 | ANI must be either one or eight digits in length. Call routed to default ACD DN as ANI failure. Output data: TRK trktn ANI ani_count ani_digits |
| ERR5304 | ANI digit is must be 1-10, where 10 is the digit 0. Call routed to default ACD DN as ANI failure. Output data: TRK trktn ANI ani_count ani_digits |
| ERR5305 | ANI was not received within 4 seconds. Call routed to default ACD DN as ANI failure. Output data: TRK trktn ANI ani_count ani_digits |
| ERR5306 | Digit dialed exceed maximum allowed. More than 10 digits received. |
| ERR5307 | MFR holding timeout. Call routed to default ACD DN as ANI failure. Output data: TRK trktn ANI ani_count ani_digits |
| ERR5308 | Could not allocate the M911 auxiliary Call Register. Call routed to default ACD DN as ANI failure. Output data: TRK trktn ANI ani_count ani_digits |
| ERR5309 | x y No music route for telephones defined for customer x using the FTC table y with XTT=YES. |
| ERR5310 | l s c u x No music route defined for the trunk at TN l s c u using the FTC table x with XTT=YES. |
| ERR5313 | CP to CP Cable Loss. The CP to CP cable is either disconnected or faulty. |
| ERR5314 | The remote CMB has lost power. |
| ERR5315 | Cannot turn on memory protection. Input address is invalid. |
| ERR5316 | Cannot turn off memory protection. Input address is invalid. |
| ERR5317 | IPB parity threshold exceeded. |
| ERR5318 | IPB IRQ threshold exceeded. Interrupt has been disabled. |
| ERR5319 | IPB IRQ interrupt has been re-enabled. |
| ERR5320 | Error occurred initializing CP. |
| ERR5321 | Failure occurred opening IPB database. |
| ERR5322 | CP database I/O error. |
| ERR5323 | IPB database I/O error. |
| ERR5324 | l s c u The message received (Barring, Busy Tone, Line Break, Polarity Change, Seize
Acknowledge) is not supported by the Class of Service defined on the trunk unit. Trunk
disabled. Mismatch between hardware and software data base. (Feature is XFCOT/XDID.) Action: Reenable trunk to force software download. |
| ERR5325 | l s c Undefined PPM ID on Card {l s c}; PPM ID unchanged on card: hardware and
software configurations no longer match. If PPM ID was invalid or undefined before, PPM
has been disabled by card for all units on Card. Action: Reconfigure PPM ID for card. |
| ERR5326 | l s c Undefined Busy Tone Id on Card {l s c}; Busy Tone ID unchanged on card: hardware
and software configurations no longer match. If Busy Tone ID was invalid or undefined
before, Tone supervision is not guaranteed to work for any unit on the card. Action: Reconfigure Busy Tone ID for card. |
| ERR5327 | l s c u xxx xxx ... xxx Configuration not Supported on trunk {unit TN}. Trunk is
disabled. Configurations not supported are XXX (XXX ... XXX), where xxx is one of: BUF PPM
BTS BAR BAT DGC ATG. Action: Examine Route and Trunk Unit configuration and change the offending configuration. Where: ATG = Autoguard (defined on unit: SEIZ) BAR = Barring/Line Break Alarm (defined on unit Class of Service) BAT = Battery Supervision (ARF BAT LBS) (defined by STYP in LD 16 for trunk unit). BTS = Busy Tone Supervised: (defined by STYP in LD 16 for trunk unit). BUF = PPM Buffered/Unbuffered: (defined on route) DGC = DID Digit Collection Type (DIP/DTN/MFC) (defined on unit Class of Service and route) PPM = PPM Enabled/Disabled: (defined on route) |
| ERR5328 | l s c u Dialing Speed downloaded is not supported on the unit. Dialing speed for the
unit is not changed on the card. Hardware and software databases no longer match. Action: Change the dialing speed of the unit. |
| ERR5329 | l s c Companding law downloaded is not supported on the card. Companding law on the
card is not changed. Hardware and software databases no longer match. Action: Change the companding law of the system or change the card. |
| ERR5330 | l s c u Configuration conflict was detected on trunk unit during an audit. The configuration as specified for the unit has been stored on the card. |
| ERR5331 | Seize failure on trunk to Conventional Main. CBQCM or RVQCM process was canceled. |
| ERR5332 | msgtype tn Unknown content in message type received from superloop unit. |
| ERR5333 | content msg type tn Unknown content in message type received from superloop unit. |
| ERR5334 | The SACP package is not equipped. Idle Extension Notification (IEN) or Attendant Blocking of DN (ABDN) request received from another location. |
| ERR5335 | x y Route x has a nonexistent XTDT table defined (y) and therefore no XTD could be
found. Action: Print out tables on system (LD 97) and on XTD cards (LD20) and reconfigure route with existing XTDT table. |
| ERR5336 | GPT DTSL or NT5K75AA card configured in GPT mode. Status register not accessible. Writeio failed. Pd. DTS_CLEAR_LINT |
| ERR5337 | GPT DTSL or NT5K75AA card configured in GPT mode. Status register not accessible. Writeio failed. Pd. DTS_READY |
| ERR5338 | GPT DTSL, NT5K75AA or NT5K75AA card. Data register not accessible. Write I/O failed. Pd. DTS_SEND |
| ERR5339 | GPT DTSL or NT5K75AA card configured in GPT mode. Status register not accessible. Write I/O failed. Pd. DTS_END_OF_WRITE |
| ERR5340 | GPT DTSL or NT5K75AA card configured in GPT mode. The timer has expired and the I bit is still raised in the status register. Pd. DTS_END_OF_WRITE |
| ERR5341 | GPT DTSL, NT5K35AA card or NT5K75AA card. The software wanted to send a message to the pack. The transmit FIFO on the pack was busy and there was no more output buffer available. The value entered to DTOB in the Ovl 17 may be too small. This may also be a hardware fault. Pd. DTOB_Q_MSG |
| ERR5342 | NT5K35AA card or NT5K75AA in NT mode. DTS_SEND failed in pd. SEND_DPNSS_MSG. |
| ERR5343 | GPT DTSL or NT5K75AA card in GPT mode. DTS_SEND failed in pd.DASS_INPUT. |
| ERR5344 | WRITE I/O failed. Pd. LED_OFF. |
| ERR5345 | WRITE I/O failed. Pd. LED_ON. |
| ERR5346 | Msg received from L2 but DTIB is full. The value entered to DTIB in the Ovl 17 may be too small. This may also be a hardware fault. Pd. DTS_LONG_MSG. |
| ERR5347 | DTS_SEND failed in pd. WRITE_SIG_LINK. |
| ERR5348 | Some msg were still waiting in the DTOB when the DISABLE msg is sent to the pack. DTOB has been cleared. Pd. DDSL_DIS_MSG |
| ERR5349 | Some msg were still waiting in the DTOB when the ENABLE msg is sent to the pack. DTOB has been cleared. Pd. REQ_ENABLE. |
| ERR5350 | The required FR is missing in the display IE received from SwissNet CO. The charging information is ignored. |
| ERR5351 | A FACILITY message other than the expected Camp-On activation message was received at the MCDN/DPNSS call offer Gateway. |
| ERR5352 | Could not allocate memory for Call ID table. No Call ID can be allocated. More memory may be required. |
| ERR5355 | DCH: {DCH number} (NO XBFR) Request to get an expedited buffer by the MSDL DCH application failed. |
| ERR5356 | DCH: {DCH number} EXP {Fail cause} Request to send a message through the MSDL expedited interface failed. |
| ERR5357 | DCH: {DCH number} CAUSE {Error cause} A flow control timer was found to be active for MSDL D channel. It has been reset. No action is required by the craftsperson. |
| ERR5358 | DCH: {DCH number} CAUSE {Error cause} There should be an active flow control timer for the MSDL D-channel. The flow control state has been reset. No action is required by the craftsperson. |
| ERR5359 | Under/Overflow condition in converting ICCL Tandem Count to/from IDA Loop Avoidance Count. |
| ERR5360 | tn Loss Plan conflict found on an IPE trunk during audit parameter download. The Loss Plan stored in the IPE trunk firmware for the unit has been reset to the Loss Plan specified in the audit message. |
| ERR5361 | Unable to allocate NPID table block in memory. |
| ERR5362 | Invalid format of the dialed (ADR) digits received over 911E trunk. |
| ERR5363 | Dialed (ADR) digits not received within specified time. 911 call treated as ANI failure. |
| ERR5364 | NPID table does not exist for the 911 route. Action: Check RDB for the 911 route. |
| ERR5365 | M911_NPID_MHPTR is Nil. |
| ERR5367 | Wrong configuration for NAS Routing when the attendant is in Night Service. The
following may indicate the problem: 1. NAS table is empty 2. Night DN cannot be defined as DSC 3. Night DN is not allowed to have any forward of any type (CFWAC, FBA, HTA, EHTA, HBTA) |
| ERR5368 | n Italian CO special services: route associated to the ITXX FFC code is not configured anymore. Where: n = is the route originally configured for ITXX. |
| ERR5369 | l s c u i Invalid database configuration. Assigned authcode entered is not a valid authcode in OVL 88, where: l = loop, s = shelf, c = card, u = unit, and i = index of the assigned authcode |
| ERR5370 | tn USCR being accessed, but customer SCPL is not defined. |
| ERR5371 | tn Set has CLS USRA but FFC package is not equipped. |
| ERR5384 | The total number of messages in queue exceeds the predefined number defined in LD 17. The oldest message will be discarded in order to make room for more. The deleted messages will be displayed following this error message. |
| ERR5385 | The message has been retransmitted for the specified number of times. This message will be discarded. This deleted message will be displayed following the error message. |
| ERR5386 | Failed to allocate a CR for PMSI outgoing message. |
| ERR5387 | a b c d The PMSI outgoing message is exceed the maximum length. The character will be ignored, where: a = address of the CR contains the message, b = AUXPM, MAINPM, c = NAK counter, timeout counter, retransmission flag, and d = message length |
| ERR5388 | A digit other than 1 or 0 was entered for message monitoring option from a maintenance telephone. |
| ERR5389 | A non-polling Call Register was found when auditing the PMSI Call Registers. |
| ERR5390 | Failed to allocate polling Call Register during initialization. |
| ERR5391 | The primary port is not configured. Therefore, the message monitoring commands cannot be executed from LD 37, or from a maintenance telephone. |
| ERR5394 | xy The customer number in the CDR Record uploaded from the MPH (Meridian Packet
Handler) is invalid. It is possible that the data stored in the MPH is out of sync with
the switch x = Customer Number received from MPH (decimal) y = MPH loop number (Decimal) |
| ERR5396 | Call is dropped due to TSP database change. |
| ERR5397 | Service operation violated. |
| ERR5398 | One of the following has occurred: 1. The specified RAN route is not configured. 2. The specified route is not configured as a RAN route. 3. The RAN route is configured but no RAN member exists. |
| ERR5398 | c dn For customer "c", DISA RAN "dn", either the DISA RAN is
defined with an invalid RAN route, or the route has no trunk member. Action: The system administrator should verify the data base configuration. |
| ERR5399 | Attendant Blocking of DN (ABDN) feature is not enabled. |