ERR4200 - 4299
| ERR4200 | Speed Call list check failed. |
| ERR4201 | Speed Call list CR setup failed. |
| ERR4202 | Speed Call indexing failed. |
| ERR4203 | Speed Call entry pointer nil. |
| ERR4204 | Speed Call digits to CR failed. |
| ERR4205 | Pretranslation table being removed. |
| ERR4220 | Secondary Control register on MSI card (QPC584) failed R/W test. Action: Check the MSI card and associated cabling. |
| ERR4221 | MSI reading from backup device when it should be reading from primary device. |
| ERR4222 | Auto-terminating DN defined in the trunk block for this ACD DNIS call is not an ACD DN. |
| ERR4225 | 500/2500 Set DN cannot be defined until CPND feature is configured for that set. DATA:
500/2500 set DN and packed TN Action: Use LD 10 to configure CPND feature. Use LD 95 to configure ANY Name first. |
| ERR4226 | xx Insufficient storage for CPND Name. Where: xx = DN or DIG group and member numbers. Action: Add memory or relocate CPND Logic page. |
| ERR4227 | xx Insufficient storage for DIG name table. Where: xx = DN or DIG group and member
numbers. Action: Add memory or relocate CPND Logic page. |
| ERR4228 | Wrong I.E. for message type. |
| ERR4229 | Wrong I.E. for STATUS message. |
| ERR4230 | Wrong I.E. for RELease message. |
| ERR4231 | Wrong I.E. for RESTart message. |
| ERR4232 | Wrong I.E. for CONNect message. |
| ERR4233 | Wrong I.E. for SETUP message. |
| ERR4234 | Wrong I.E. for PROGress message. |
| ERR4235 | Wrong I.E. for CALL PROCeeding message. |
| ERR4236 | Wrong I.E. for ALERTing message. |
| ERR4237 | Wrong message type. |
| ERR4238 | Wrong coding standard. |
| ERR4239 | BC - extension bit not right. |
| ERR4240 | BC - information transfer not supported. |
| ERR4241 | BC - information transfer rate/mode not supported. |
| ERR4242 | BC - layer1 protocol id not correct. |
| ERR4243 | BC - rate is not correct. |
| ERR4244 | General location not supported. |
| ERR4245 | Cause value not supported. |
| ERR4246 | Channel id octet3 error. |
| ERR4247 | Channel id octet5 error. |
| ERR4248 | Channel number not exist. |
| ERR4249 | Extension bit wrong in cause. |
| ERR4250 | Extension bit wrong in connected number. |
| ERR4251 | Extension bit wrong in redirecting number. |
| ERR4252 | Extension bit wrong in redirection number. |
| ERR4253 | Extension bit wrong in channel number. |
| ERR4254 | Extension bit wrong in progress indicator. |
| ERR4255 | Extension bit wrong in NSF. |
| ERR4256 | Extension bit wrong in calling party number. |
| ERR4257 | Extension bit wrong in called party number. |
| ERR4258 | Extension bit wrong in restart. |
| ERR4259 | Detected invalid contents for call reference of an incoming ISDN message. Message is ignored. There may be a compatibility problem with the far-end. |
| ERR4260 | CREF flag in SETUP is incorrect. |
| ERR4261 | State message error, protocol violation. |
| ERR4262 | NTWK ID not correct in TNS. |
| ERR4263 | No RESTart ACK message received. |
| ERR4264 | Message received in NULL state. |
| ERR4265 | Mandatory Channel ID missing in ALERTing. |
| ERR4266 | Mandatory Channel ID missing in CONNect. |
| ERR4267 | Service in NSF does not match service route. |
| ERR4268 | PROGRESS INDICATOR not supported. |
| ERR4269 | ZERO length for mandatory IE. |
| ERR4270 | ZERO length for option IE. |
| ERR4271 | TNS, BAD NTWK ID, TYPE/PLAN. |
| ERR4272 | BC - layer id not correct. |
| ERR4273 | Incorrect TNS Network ID. |
| ERR4274 | Message Length exceeds buffer size (261). |
| ERR4275 | Protocol discriminator is not compatible with a Message length greater than 2. |
| ERR4276 | Maintenance message is only allowed in specific DCH interface. |
| ERR4277 | c dn ifdn Invalid Interflow destination. Where: = customer, dn = ACD-DN, ifdn = Interflow DN. |
| ERR4278 | c dn ifdn Invalid Night Call Forward destination specified. Where: = customer, dn = ACD-DN, ifdn = Interflow DN. |
| ERR4279 | No Service Ack message received. |
| ERR4280 | Use LD 92 to diagnose the ADM TN. |
| ERR4281 | Message input received from a 64 k data module has no Call Register available. |
| ERR4282 | d b No response from far-end to this PRA call. Where: d = DCHI number, b = Bchannel
number. Action: Check the D-channel link on near and far-end switches. |
| ERR4283 | Both DCHs have been released. Establish the DCH. |
| ERR4285 | 1. ACNT key defined but no ADS block defined, OR 2. This agent is not an acquired ICCM
agent (Rls 22). Action: Either take out ACNT key or define ADS block. |
| ERR4286 | Message count on the loop exceeds the threshold value. Action: Refer to any OVD messages previously printed, and check the hardware for defects that generate an overload condition. Rearrange the TNs to another location or they may be disabled. Reconfigure the Loop. |
| ERR4287 | Customer number greater than 31 while CDRE is not packaged. Action: Refer to any OVD messages previously printed, and check the hardware for defects that generate an overload condition. Rearrange the TNs to another location or they may be disabled. |
| ERR4288 | Route number is greater than 127 while CDRE is not packaged. |
| ERR4289 | Route number for music route is not a music route. |
| ERR4291 | Music route is undefined. |
| ERR4293 | Both DCHs out-of-service. Action: Release/Establish both DCHs. |